Search results for query: *

-SAI Scout -JAE stock -Millett TRS-1 scope on Sadlak mount -Sadlak gas piston and spring guide, Tubb springs -NM 4.5" trigger pull -Tango Down bipod, Accu Shot monopod 5 shots, 0.80" group, 100 yards, 168HPBT Black Hills, bench 5 shots, 0.71" group, 100 yards, 168HPBT Federal Match, bench...

Proud new Savage owner, and Im trying to take the bolt out -- following the instructions it says to put the safety on, pull trigger and pull back bolt handle at the same time. I am cranking pretty hard on both and the bolt is not pulling out rearward. I'm pulling hard enough that the back half...

Proud new Savage owner, and Im trying to take the bolt out -- following the instructions it says to put the safety on, pull trigger and pull back bolt handle at the same time. I am cranking pretty hard on both and the bolt is not pulling out rearward. I'm pulling hard enough that the back half...

What scope rings do I need to get for my Remington 550-1 .22 rifle? They are not your typical .22 mount..

I have a detachable carry handle with a rear sight marked 6/3. I followed the directions on AR15.com (link) on how to do a Revised Improved Battle Sight Zero using an 8/3 rear sight. So I followed the directions and moved the rear wheel -4 clicks. Everything looks good, I have my 100 yard...

I found some rust in the barrel of my relatively new marlin 30-30-- so I ran a few oiled up patches through the bore, followed by a few oiled patches draped over a copper brush. I then sprayed some anti rust spray down the barrel and let it soak, then followed up with more oiled patches draped...

Oleg, I know you specialize in 2A posters, and for the longest time I have envisioned a 2A cartoon, however I do not have the talent to draw it. So I will describe it. The cartoon is a blank rectangle frame. The right side of the cartoon is a gun shop with a line out the door of citizens...

I have a 28" Franchi I-12 and Ive been told several times that its a "goose gun". What attributes determines what is for goose, or for smaller birds, or for larger game like deer? It seems to me that I can use it for goose, lighten the load for smaller birds, and use rifled slugs for deer. It...

I lost the owners manual on my Franchi I-12, how do I remove the bolt? Does it have to be open to allow the knob to twist and disassemble?

I am looking to get a 30-30 or 30-06 if possible. I have only shot my friends Marlin 30-30 lever action and I really, really liked it and figured I would ask around for any recommendations on models and calibers. It will mostly be used for target shooting. Any thoughts?

In the past two weeks, i have had both my Kimber Warrior and Kimber Eclipse go into burst fire while at the range. I've owned both these pistols for a year and have been great. Kimber Warrior ------------------- Dropped in a new Kimber aluminum trigger and shot 300+ rounds fine, then it...

Fired a shot from the .22 rifle, bullet shot, brass got stuck real good. In my efforts to tap it out I've managed to punch out the rim of the brass as well. So I have a perfect cylinder stuck inside the barrel. There is an edge of brass left that I have been trying to get out with angled needle...

I am working on my 1911 .45 target pistol and I have been looking into a bushing compensator to reduce muzzle flip. What are the best brands for bushing compensator's? Also, I have seen "weighted" extensions on pistols to aid in muzzle flip - what is this called? Please feel free to...

Does anyone have plans for the 100-year anniversary of the 1911? Three years and counting!

What are my options for adding a little more bite to the rear slide grip? The finished slide of my Kimber Warrior is a little slippery at times (although manageable) and I wanted to ask around. I suppose the only option would be to strip the paint off the slide, shave the rear slide grip...

What are some of your recommendations for feeler gages and other useful tools for tuning a 1911?

I want to refinish my Kimber Eclipse, in particular remove all of the black oxidation (?) from the upper and lower frame. I want to keep the brushed finish as seen on the slide. 1) Can anyone recommend a good refinisher/gunsmith who can do this? 2) Perhaps I could do it myself...

Does anyone have the Ergo grips (the rubber ones not the hard nylon ones)? If you have the rubber grips is it super hard rubber or does it give a little? When you tap it quickly with your finger does it have a little bounce or does it make a hard sound? Do you like yours? Seen here:

I keep having a frequent problem, in the middle of a magazine the round is being loaded successfully from the magazine, it slides under the extractor, but gets caught by the barrel 3/4 into battery. When looking down at the ejection port you can see the round behind the extractor...its just the...

What is the deal with 7rds magazines vs 8rds magazines? My Kimber Eclipse has 8 rds and my Kimber Warrior has 7 rds in the magazine.... they are both the same size pistols, and both the same size magazine, just one is 8 and the other is 7.... what gives?