Search results for query: *

I sold my rifles and would like to sell the last cases I have. 20 - 220 Swift and 100 - .22-250. The Swift cases are factory new unprimed. The 250's are all good looking cases. What should I ask? Thanks Older than Dirt Tom

Anyone whose had a frame break or at least seen one that was broken, please weigh in.

I have 700 M1 carbine cases that have flash holes that look like this: Trash'em? Or what?... Any advice is appreciated. Thanks Tom

Ammo came in a 50 round box labeled... Head stamp ... 30 m1 and 99 or more likely 59 (very faint stamp). Any help id'ing is appreciated Thanks Tom

deleted, found the answer

An M1 Carbine is waiting for me at my FFL, I've been looking forward to having one for a while. I'm ordering reloading equipment and want to get your advice on the Forster 3 in 1 that fits on the Forster Original. This would cost me about double what pilots, collets and a de-burring tool would...

Getting stuff together to reload M1 Carbine. I'll probably buy a few brands of loaded ammo to test the rifle and gather brass. Are there any brands better than the others or is there anything to avoid? Thanks

I have an M1 Carbine on the way to me and need ammo for it. There is no .30 carbine available to me here so I'll need to order on line. I could get a half a dozen boxes of various brands or a 500 round case of one brand. All brass since I'll be reloading it when the dies get here. Probably...

I'm looking for an extra magazine or two to go with a Mak that I ordered from Classic. Ran across ads on Ebay some with a hump some without. Any other sources for these magazines? Thanks Tom

I'd like to put this Hogue Monogrip in the Pay it Forward thread. I need help identifying what revolver it fits. I bought them at a gun show for my S&W 15-3 but it didn't fit.

You are loading 9mm on a progessive, the ideal COL for the powder and bullet combination is 1.125..... What are you willing to accept either side of the ideal? And..... Are dies like the Redding competition seating dies for pistol calibers really the cats meow?

New to me Sig is shooting to the right. I'm trying to be easy on the sight screw but it will not budge. I tried heating with a butane lighter...no go. Any suggestions would be appreciated. Thanks Tom Edit... target shot at 10 yards from a rest , Win White box 95gr flat point.

My wife started shooting more than she was since she got a Bersa Thunder .380. So it's time for me to start reloading .380. I'll be reloading soft shooting practice ammo. I reload 9mm using Hornady dies, except for a Redding taper crimp die, but I have a second set of 9mm dies made by Lee...

I have roughly 100 # of range scrap. I'm mulling over the efficacy of melting them to make ingots. I reload but don't cast bullets at this time, perhaps I'd sell the lead ingots at the biannual gun show in town. What's your best guess on the amount of lead ingot that's recoverable from the...

Stopped into my LGS and bought an old Remington 1100 LW 20 without checking the choke. I need some help locating and deciphering the code for the choke. Thanks Tom

I'm currently working with an RCBS 505 and a digital scale. The digital scale has proved to be unreliable and I don't use it for powder weights any more. The 505 is fine but I have large hands and a tremor in my hands so it gets a little tricky to move the weights sometimes. I'd appreciate...

I'm new to reloading for 9mm and I'm testing various bullets. This test is for Berry's 147 over 3.0g of Tite Group. The books call for Min COl of 1.160 to 1.170 depending on the source. This COL will not pass the drop test in a CZ75b barrel. I found the best I could do was about 1.082. From...

I'm researching the use of plated (115gr RN) bullets in 9mm and came across a statement about crimping too tight and causing the plating to crack and putting yer accuracy in der terlit. Is this an issue, can you see the cracking? Crimp question #2:Switching separate crimp die from from FMJ to...

9mm... Lee dies ...initial set up... Hornaday LNL AP. The shells are hanging up in the expander when the die lets go of the shell there's a hitch in the press. I can repeat this issue with the die removed from the press so I don't think it's a timing problem. I've contacted Lee, they suggested...

Would you recommend this case loader. I load on a LNL AP.